AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Flir lepton usb1/29/2024 ![]() The firmware of the DIY-Thermocam is completely open-source and written in C/C++. In case you want to extend the existing featureset with your own functionality, that's possible too. It can also communicate to the PC over the USB serial protocol, in order to stream thermal images or change settings remotely. Dual Thermal and Visible OEM Camera Module. Adjust parameters in real time using the RHP Lepton GUI when connected to a PC. ![]() The DIY-Thermocam offers a wide range of features, like adding temperature points, changing temperature range limits, displaying hot or cold temperatures only, saving single images or a series of images (video or timelapse) to the integrated storage, changing the color scheme, etc. Intelligent polarity sensing protection - powered from the 4-Pin JST port to USB 5VDC power source. ![]() Once the Thermocam is connected to the PC, it will show up as a mass storage device and allows you to transfer thermal images from or to the device. Flashing the firmware is easy and can be done without any programming knowledge on any operating system over the command line interface. Input Supply Voltage: 2.8 V, 1.2 V, 2.5 V to 3.The Device Firmware provides a lot of functionalities, that can be accessed over the 3.2" TFT LCD touch screen.Sensor Technology: Uncooled VOx microbolometer.Non-Uniformity Correction (NUC): Automatic with shutter.The radiometric Lepton captures accurate, calibrated, and non-contact temperature data in every pixel. Image Optimization: Factory configured and fully automated With a focal plane array of 80圆0 active pixels, this Lepton easily integrates into native mobile-devices and other electronics as an IR sensor or thermal image sensor.Array format: 80 × 60, progressive scan.Optimum Temperature Range: -10☌ to +80☌.Non-Operating Temperature Range: -40 ☌ to +80 ☌.Mechanical Interface: 32–pin socket interface to standard Molex® socket.into the Purethermal board adapting I/O camera pins to the USB interface. The mode is selected using the SYS FFC Mode Control Command, described in the software IDD. two different thermal cameras: a low-cost FLIR Lepton 3.5 21 (160 x 120. For cameras with a shutter, FLIR sets the default at the factory to auto FFC, but it is possible to change the mode to manual FFC. Control Port: CCI (I2C-like), CMOS IO Voltage Levels There are three flat-field correction modes for Lepton. It ships preconfigured to operate as a plug-and-play UVC 1.0 USB thermal webcam that will work with standard webcam apps such as VLC Media Player on PC, Linux.Output image independent of camera temperature. Tuning the Vsync delay parameter in the Lepton SDK can help with lepton-host communication. It is worth a try if issues are present where lepton is not working consistently. It ships preconfigured to operate as a plug-and-play UVC 1. Pure Thermal 2 by GetLab Adding a delay between the Interrupt driven by V sync and SPI read may be necessary in some circumstances. Spectral Range: Longwave infrared, 8 µm to 14 µm The PureThermal 3 FLIR Lepton Smart I/O Module is a hackable thermal webcam module for the FLIR Lepton Longwave Infrared (LWIR) camera core.Scene Dynamic Range: -10-140 ☌ (high gain) up to 450☌ (low gain) typical. ![]() Radiometric Accuracy: High gain: Greater of +/- 5☌ or 5% (typical) Low gain: Greater of +/- 10☌ or 10% (typical) Compatible with all production FLIR Leptons, including radiometric 2.5 and 3.5 cores 9 Hz color video over usb using the USB UVC class STM32F412 ARM.Output Format: User-selectable 14-bit, 8-bit (AGC applied), or 24-bit RGB (AGC and colorization applied) The FLIR Lepton 2.5 - Thermal Imaging Module is a radiometric-capable long wave infrared (LWIR) camera solution that is smaller than a dime, fits inside a smartphone, and is less expensive than traditional IR cameras.Input Clock: 25-MHz nominal, CMOS IO Voltage Levels.Shipping outside of the US Click here for info We have an order limit of 1 per customer on this product. This product requires other products in order to function properly. Effective Frame Rate: 8.6 Hz (commercial application exportable) FLIR Lepton 2.5 - Thermal Imaging Module SEN-16465 RoHS 209.95 Notice.The Flir Lepton thermal imaging modules are used in a vast array of commercial and industrial applications, such as Mobile Phones, Gesture Recognition, Building Automation, Thermal Imaging and Night Vision. With a focal plane array of 80圆0 active pixels, this Lepton easily integrates into native mobile-devices and other electronics as an IR sensor or thermal image sensor. The FLIR Lepton® 2.5 Thermal Imaging Module is a radiometric-capable long-wave infrared (LWIR) camera solution that is small enough to fit inside a smartphone and is less expensive than traditional IR cameras.
0 Comments
Read More
Leave a Reply. |